H3c-technologies H3C WX6000 Series Access Controllers Manual de usuario Pagina 118
- Pagina / 179
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
10-4
For example, in the output rule, if you configure to output information with severity level being
informational, the information with severity level being emergency through informational will be output.
Table 10-1 Severity description
Severity Severity value Description
Emergency 0 The system is unusable.
Alert 1 Action must be taken immediately
Critical 2 Critical conditions
Error 3 Error conditions
Warning 4 Warning conditions
Notice 5 Normal but significant condition
Informational 6 Informational messages
Debug 7 Debug-level messages
Eight Output Destinations and Ten Channels of System Information
The system supports eight information output destinations, including the console, monitor terminal
(monitor), log buffer, log host, trap buffer, SNMP module, Web interface (syslog) and log file. The
specific destinations supported vary with ACs.
The system supports ten channels. The eight channels 0 through 6, and channel 9 are configured with
channel names, output rules, and are associated with output destinations by default. The channel
names, output rules and the associations between the channels and output destinations can be
changed through commands. Besides, you can configure channels 7, and 8 without changing the
default configuration of the eight channels.
Table 10-2 Information channels and output destinations
Information
channel number
Default channel
name
Default output
destination
Description
0 console Console Receives log, trap and debugging information.
1 monitor Monitor terminal
Receives log, trap and debugging information,
facilitating remote maintenance.
2 loghost Log host
Receives log, trap and debugging information
and information will be stored in files for future
retrieval.
3 trapbuffer Trap buffer
Receives trap information, a buffer inside the
router for recording information.
4 logbuffer Log buffer
Receives log and debugging information, a
buffer inside the router for recording information.
5 snmpagent SNMP module Receives trap information.
6 channel6 Web interface Receives log information.
7 channel7 Not specified Receives log, trap, and debugging information.
8 channel8 Not specified Receives log, trap, and debugging information.
9 channel9 Log file Receives log, trap, and debugging information.
- Configuration Guide 1
- All Rights Reserved 2
- Trademarks 2
- Preface 3
- GUI conventions 4
- Symbols 4
- Network topology icons 4
- Obtaining Documentation 6
- Technical Support 6
- Documentation Feedback 6
- Table of Contents 8
- 2 Typical Network Scenarios 13
- Unified Switch Networking 14
- 3 Feature Matrixes 15
- 4 Command Matrixes 29
- Introduction 61
- Configuring Ping 61
- Tracert 64
- System Debugging 65
- 6 NTP Configuration 69
- NTP Message Format 71
- Operation Modes of NTP 72
- Symmetric peers mode 73
- Broadcast mode 73
- NTP Configuration Task List 74
- NTP Configuration Examples 83
- delay disper 89
- Root delay: 40.00 ms 89
- 7 SNMP Configuration 93
- SNMP Protocol Versions 94
- MIB Overview 94
- SNMP Configuration 95
- Configuring SNMP Logging 97
- Configuring SNMP Traps 98
- Configuring Trap Parameters 99
- Network requirements 101
- Configuration procedure 101
- 8 MIB Style Configuration 104
- 9 RMON Configuration 105
- RMON Groups 106
- Alarm group 107
- Private alarm group 107
- Configuration Procedure 109
- Configuration Prerequisites 109
- Information Center Overview 115
- System Information Format 120
- 11 NQA Configuration 136
- Basic NQA concepts 139
- NQA Configuration Task List 140
- Configuring the NQA Server 141
- Enabling the NQA Client 141
- Creating an NQA Test Group 142
- Configuring DHCP Tests 143
- Configuring DNS Tests 144
- Configuring FTP Tests 145
- Configuring HTTP Tests 146
- Configuring UDP Jitter Tests 147
- Configuration prerequisites 148
- Configuring UDP jitter tests 148
- Configuring SNMP Tests 149
- Configuring TCP Tests 150
- Configuring UDP Echo Tests 150
- Configuring UDP echo tests 151
- Configuring Voice Tests 152
- Scheduling an NQA Test Group 157
- NQA Configuration Examples 158
- 12 Index 178
Relacionado con productos y manuales para Routers H3c-technologies H3C WX6000 Series Access Controllers
(85 paginas)
(13 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales