H3c-technologies H3C SecBlade NetStream Cards Manual de usuario Pagina 103
- Pagina / 349
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
88
[SecBlade-vlan5] port gigabitethernet 0/2
# Create VLAN 10 and assign GigabitEthernet 0/3 to it.
[SecBlade-vlan5] vlan 10
[SecBlade-vlan10] port gigabitethernet 0/3
[SecBlade-vlan10] quit
# Create VLAN-interface 5 and configure its IP address as 192.168.0.10/24.
[SecBlade] interface vlan-interface 5
[SecBlade-Vlan-interface5] ip address 192.168.0.10 24
[SecBlade-Vlan-interface5] quit
# Create VLAN-interface 10 and configure its IP address as 192.168.1.20/24.
[SecBlade] interface vlan-interface 10
[SecBlade-Vlan-interface10] ip address 192.168.1.20 24
[SecBlade-Vlan-interface10] return
2. Configure PC A
# Configure the default gateway of the PC as 192.168.0.10.
3. Configure PC B
# Configure the default gateway of the PC as 192.168.1.20.
Verification
1. The PCs can ping each other.
2. Display brief information about Layer 3 interfaces on SecBlade to verify the configuration.
<SecBlade> display ip interface brief
*down: administratively down
(s): spoofing
Interface Physical Protocol IP Address Description
Vlan-interface5 up up 192.168.0.10 Vlan-inte...
Vlan-interface10 up up 192.168.1.20 Vlan-inte...
Port-based VLAN configuration
Introduction to port-based VLAN
Port-based VLANs group VLAN members by port. A port forwards traffic for a VLAN only after it is
assigned to the VLAN.
Port link type
You can configure the link type of a port as access, trunk, or hybrid. The link types use the following
VLAN tag handling methods:
• An access port belongs to only one VLAN and sends traffic untagged. It is usually used to connect
a terminal device unable to recognize VLAN tagged-packets or when there is no need to separate
different VLAN members. As shown in Figure 30,
Device A is connected to common PCs that cannot
r
ecognize VLAN tagged-packets, and you must configure Device A’s ports that connect to the PCs
as access ports.
- H3C SecBlade NetStream Card 1
- Preface 3
- GUI conventions 4
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- CLI configuration 16
- Entering the CLI 17
- Command conventions 17
- Undo form of a command 18
- CLI views 18
- Using the CLI online help 19
- Typing commands 20
- Typing incomplete keywords 21
- Configuring command aliases 21
- Configuring CLI hotkeys 22
- System Mana 23
- Maintenance Command Reference 23
- Checking command-line errors 24
- Using command history 24
- Controlling the CLI display 25
- Filtering output information 26
- Character Meanin 27
- Remarks 27
- Login methods 35
- Users and user interfaces 36
- Numbering user interfaces 36
- CLI login 37
- Login procedure 38
- Logging in through telnet 47
- ACSEI timers 58
- ACSEI startup and running 58
- NMS login 61
- NMS login example 63
- User login control 65
- NMS users 68
- Interface configuration 70
- General configuration 71
- IP addressing configuration 80
- Special IP addresses 81
- Subnetting and masking 81
- Configuring IP addresses 82
- 172.16.1.1/24 83
- 172.16.2.1/24 sub 83
- 172.16.1.2/24 83
- 172.16.2.2/24 83
- IP routing overview 85
- Dynamic routing protocols 86
- Routing preference 87
- Route recursion 87
- Static routing configuration 89
- Configuring a static route 90
- What is policy-based routing 93
- Configuring PBR 94
- Configuring local PBR 96
- Configuring interface PBR 96
- VLAN configuration 98
- VLAN fundamentals 99
- VLAN types 100
- Protocols and standards 100
- VLAN interface overview 101
- Configuration procedure 101
- Network requirements 102
- Verification 103
- Port link type 103
- Default VLAN 104
- To do... Use the command… 109
- Remarks 109
- Overview 110
- Working mechanism 115
- Configure the SecBlade card 119
- GE3/0/1 GE3/0/2 121
- XGE2/0/1 121
- ARP configuration 128
- Operation of ARP 129
- Configuring ARP 130
- ARP configuration example 133
- Gratuitous ARP configuration 135
- Configuring gratuitous ARP 136
- Proxy ARP configuration 137
- Local proxy ARP 138
- Enabling proxy ARP 139
- 2. Configure the SecBlade 143
- ACL configuration 144
- Match order 145
- ACL rule numbering 145
- ACL configuration task list 146
- Configuring an ACL 146
- Copying an IPv4 ACL 149
- Packet filtering with ACLs 150
- ACL configuration example 152
- NetStream overview 154
- How NetStream works 155
- Flow aging 155
- NetStream data export 156
- NetStream export formats 157
- NetStream filtering 157
- NetStream sampling 157
- IPv4 NetStream configuration 159
- Enabling IPv4 NetStream 160
- To do… Use the command… 166
- IPv6 NetStream configuration 167
- Configuration considerations 172
- Configuring the host device 173
- Configuring the NSC 175
- 1. Configure the Device 176
- Device management 188
- Configuring the system time 189
- Displaying the system time 189
- Configuring banners 192
- Rebooting the device 195
- Configuring a scheduled task 196
- NOTE: 204
- NTP configuration 205
- How NTP works 206
- NTP message format 207
- Operation modes of NTP 208
- Symmetric peers mode 209
- Broadcast mode 209
- NTP configuration task list 210
- Configuration prerequisites 213
- NTP configuration examples 214
- SecBlade and Device 217
- Automatic configuration 218
- Address acquisition process 220
- File types 221
- TFTP request sending mode 223
- FTP configuration 224
- Configuring the FTP client 225
- 10.1.1.1/16 229
- 10.3.1.1/16 229
- 10.2.1.1/16 229
- Configuring the FTP server 230
- 3. Upgrade SecBlade 233
- TFTP configuration 235
- Configuring the TFTP client 236
- File management 239
- Performing file operations 241
- Renaming a file 242
- Copying a file 242
- Moving a file 242
- Deleting a file 242
- Performing batch operations 243
- Setting prompt modes 245
- Example for file operations 246
- Configuration file overview 247
- Introduction 248
- Configuration rollback 250
- Configuration task list 250
- Device software overview 256
- Software upgrade methods 257
- Basic concepts in hotfix 258
- Patch status 259
- DEACTIVE state 260
- ACTIVE state 260
- RUNNING state 261
- One-step patch installation 262
- Loading a patch file 263
- Activating patches 263
- Confirming running patches 264
- Stopping running patches 264
- Deleting patches 264
- Network requirement 265
- Hotfix configuration example 267
- Configuring ping 268
- Tracert 269
- System debugging 270
- Information center overview 273
- System information format 277
- PRI (priority) 278
- Managing security logs files 287
- 1.1.0.1/16 1.2.0.1/16 290
- SNMP configuration 295
- SNMP configuration task list 296
- Configuring SNMPv3 297
- Configuring SNMP logging 299
- Configuring SNMP traps 299
- Enabling SNMP traps 300
- Configuring trap parameters 300
- SNMP configuration examples 302
- SNMPv3 configuration example 303
- 1.1.1.2/24 304
- XGE4/0/1XGE0/0 304
- 1.1.1.1/24 304
- MIB style configuration 307
- RMON configuration 308
- RMON groups 309
- Alarm group 310
- Private alarm group 310
- XGE4/0/1 314
Relacionado con productos y manuales para La Seguridad H3c-technologies H3C SecBlade NetStream Cards
(66 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales